Looking for the Greatest Hits
As a fan of the Precision Matters column
by Gerald Davis, I recommend that our
Solid Works value-added reseller sales team
share your columns with customers and
Where can current or past columns be
looked up? I didn’t see the archive on www.
Senior Manager Special Custom Projects
Editor’s Note: You can find the Precision Matters archive at
http://www.thefabricator.com/author/gerald-davis. If you
scroll down, you’ll find his columns providing advice on 3-D
solid modeling. ;anks for reading ;e FABRICATOR.
Clearing the Air on Lift Trucks
Good of the publication to tackle this topic [“No-, low-emissions lift trucks clear the air,” ;e FABRICATOR, August 2013, p. 76], but clarifications are needed. Perhaps it
would be good to clear the air about these.
In particular, it should be noted that these diesel fume
exhaust regulations came about because the exhaust’s
constituents, such as particulate matter and NOx, generally are considered bad for humans. ;erefore, the newest regulations address the need to reduce these even
further. A link to cancer is not the reason. No direct link
has been established either medically or legally.
Also it should be noted that the National Clean Diesel
Campaign (NCDC) has not put out the Tier 4 schedule, but
the Environmental Protection Agency itself has. ;e NCDC
program is independent of the regulatory framework.
Another item to address is the discussion of the “tran-
sition plan” and “flexibility” guidelines. ;ese also are op-
tional programs. ;ey allow for a number of prior “tier”
newer “tier.” Some companies use them and some don’t.
Fork lift engine manufacturers would not need to submit
their plans to the EPA unless they decided to participate
in this program. ;ere is no need for engine manufacturers to submit their plans to the EPA if they are not
Finally, Toyota Material Handling is mentioned as
meeting EPA standards on their 8-series models with the
use of two engines, the 4Y and 1 DZ-III. ;is is puzzling as
the three-way catalyst;technologies are for use on spark-ignited engines and not diesel.
Editor’s Note: ;e 4Y and 1 DZ-III engines should not have
been mentioned in the section of the story covering diesel
engine advancements. ;e editors regret the error.
Knowledge on Press-related Stress?
Do you know of any survey or measurement method to
evaluate the mental stress on die setters?
Flying dies all day has to be kind of stressful, and I was
wondering how you measure that. Any guidance you can
share would be helpful.
John R. Alteneder
Assistant Manager TPS/Kaizen Group
Toyota Motor Manufacturing
Editor’s Note: While it may be helpful to find some type of
evaluation method given in other high-stress fields, such as
air tra;c controllers, emergency room personnel, or police
o;cers, we aren’t aware of any that specifically apply to
pressroom workers. If any of ;e FABRICATOR’s readers
have any ideas, we’ll pass them along.
Published by FMA Communications Inc.
833 Featherstone Road
Rockford, IL 61107-6302
815-399-8700 | Fax 815-484-7700
President & CEO, FMA Communications Inc.:
Group Publisher: Dave Brambert
Editor-in-Chief: Dan Davis, email@example.com
Senior Editor: Tim Heston, firstname.lastname@example.org
TPJ–;e Tube & Pipe Journal Editor:
Eric Lundin, email@example.com
Green Manufacturer Editor:
Kate Bachman, firstname.lastname@example.org
Practical Welding Today Associate Editor:
Amanda Carlson, email@example.com
Contributing Editor: Amy Nickel
Associate Editor: Sue Roberts
Senior Copy Editor: Teresa Chartos
Graphic Designers: Mary Mincemoyer,
Janell Drolsum, Margaret Clark, Jennifer Paulson
Publication Coordinator: Kelly Palmer
Director of Circulation: Kim Bottomley
Circulation Manager: Brenda Wilson
Data Verification Specialist: Rhonda Fletcher
Senior Fulfillment Specialist: Anna Peacock
Web Content Manager: Vicki Bell
Multimedia Specialist: Sherry Young
Senior Web Developer: Jason Bartholme
Web Developer: Johanna Albee
Jim Gorzek, firstname.lastname@example.org
Senior Account Representatives:
Sean Smith, email@example.com
Mike Lacny, firstname.lastname@example.org
Tony Arnone, email@example.com
Amy Hudson, firstname.lastname@example.org
Michael Scott, email@example.com
Patty D’Amico, firstname.lastname@example.org
Statement of Policy
As the o;cial publication of the Fabricators & Manufacturers Association, International, ;e FABRICATOR recognizes the need and importance of disseminating information about modern metal forming and
fabricating techniques, machinery, tooling and management concepts
for the metal fabricator. ;e policy of the publisher and this journal is
to be nonpartisan, favoring no one product or company. ;e representations of fact and opinions expressed in the articles are those of the
author and are not necessarily endorsed by the publisher and this journal. By including information on new products, new literature, news
of the industry, articles, etc., this impartiality is strived for and extends
to the mention of trade names. Unless product identification makes
the reference unavoidable, the generic name is used. We acknowledge
that on occasion there may be oversights and errors; the editors regret such oversights and re-emphasize their policy to be impartial at
all times. ;e publisher reserves the right to refuse advertising deemed
inappropriate for publication in ;e FABRICATOR, including ads for
classes of products and services not considered of significant interest
to the readership. “;e FABRICATOR” is a service mark and a trademark of the Fabricators & Manufacturers Association, International,
and is used, under license, by FMA Communications Inc. Standard Rate
& Data Service lists our advertising rates in Section 88. Consult SRDS or
our current rate card for full rates and data. Publications of FMA Communications Inc. maintain a policy of keeping editorial and advertising
separate to ensure editorial integrity that most benefits our readership.
Editorial content, including feature articles and press releases, is determined solely by the publisher. Editorial content cannot be purchased,
nor can it be used as a benefit of advertising dollars spent. Editorial is
free-of-charge, subject to space availability, and open to all interested
parties that submit items meeting our editorial style and format as
determined by the publisher. Note: Some photographs printed in this
publication may be taken with safety equipment removed for photographic purposes. However, in actual operation, it is recommended that
correct safety procedures and equipment be utilized.
(continued on page 14)
What ABILITIES will you gain with
Fastenal’s Industrial Vending program?
Supplies are immediately available at the
point of use, 24/7/365
Detailed usage reporting: simplifies job
costing, reduces consumption
Fastenal provides the machines, keeps them filled,
and owns the inventory until it’s dispensed
VISIT US AT FABTECH BOOTH #N2461
To learn more visit www.fastenal.com/web/vending
Oct_Fabricator_HalfPageAd.indd 1 8/27/13 9:22AM